Support
OBD Gear Indicator
Need help with OBD Gear Indicator? Contact us and we'll get back to you as soon as we can.
appsupport@synsetech.com
What You Need
- A Bluetooth LE (BLE) ELM327 adapter, sold separately. Classic Bluetooth (SPP) and Wi-Fi adapters cannot be used on iOS.
- A vehicle with an OBD-II port that reports engine RPM (PID 0C) and vehicle speed (PID 0D).
Common Questions
- The adapter doesn't appear in the scan list — Turn on "Show all devices" in Settings. Some compatible clones advertise under a different name, so check the device name carefully before selecting it. Also make sure the adapter is plugged in and the ignition is on.
- Nothing happens on the first scan — Make sure Bluetooth is switched on and that you granted the Bluetooth permission when prompted. The app waits for Bluetooth to become ready before scanning.
- The gear number is wrong — Tap the correct gear on the calibration screen. That gear is relearned on the spot, and any neighboring gear that no longer fits is cleared and learned again on your next drive.
- Auto detection never completes — Detection needs a steady speed of at least 15 km/h and 900 rpm, held for a few seconds in each gear. Hold each gear at a constant throttle; allow 5–10 minutes overall.
- You'd rather not drive to set it up — Choose "Enter gear ratios" and type in the transmission ratios, final drive ratio and tire circumference. No learning drive is needed.
- Your car reports gear directly — Choose "Read from OBD" and enter the manufacturer-specific PID (for example a Mode 22 command), then tune the data offset and scale while watching the live response.
- Green and red are swapped on the G bar — Turn on "Reverse accel./decel. direction" in Settings. Tilt and screen orientation are otherwise corrected automatically.
- The rev-match indicator doesn't appear — It is calculated from the gear ratio of the next lower gear, so it stays hidden until that gear has been learned or entered. It also needs the assist to be enabled in Settings, and a road speed of at least 15 km/h in second gear or higher.
- Where are the settings? — Tap anywhere on the main screen to reveal the settings button.
Privacy
The App collects no data. See the Privacy Policy.
For anything else, including bug reports and feature requests, please email us at the address above.
サポート
OBD Gear Indicator
OBD Gear Indicatorについてお困りのことがあれば、こちらまでご連絡ください。順次対応いたします。
appsupport@synsetech.com
必要なもの
- Bluetooth LE(BLE)対応のELM327アダプター(別売)。iOSではクラシックBluetooth(SPP)およびWi-Fi接続のアダプターは使用できません。
- エンジン回転数(PID 0C)と車速(PID 0D)を返すOBD-IIポートを備えた車両。
よくある質問
- アダプターが検索結果に出てこない — 設定の「すべてのデバイスを表示」をONにしてください。互換品は名前が一致しないことがあるため、機器名を確認してから選んでください。アダプターが挿さっていること、イグニッションがONであることもご確認ください。
- 1回目の検索で反応がない — 端末のBluetoothがONになっていること、初回の権限確認を許可済みであることをご確認ください。本アプリはBluetoothの準備完了を待ってから検索を開始します。
- ギヤ表示が違う — 検知画面で正しい段をタップしてください。その段をその場で学習し直します。段どうしの整合が取れなくなった隣の段は学習結果が解除され、次の走行であらためて学習されます。
- 自動検知が終わらない — 検知には15 km/h・900 rpm以上で、各段を数秒間一定に保つ必要があります。アクセル一定で各段を維持してください。全体で5〜10分が目安です。
- 走行せずに設定したい — 「ギヤ比を入力」を選び、各段のギヤ比・最終減速比・タイヤ周長を入力してください。学習のための走行は不要です。
- 車両がギヤ段を直接返す場合 — 「OBD直読み」を選び、車種別PID(例:Mode 22 のコマンド)を入力してください。受信データを見ながらデータ位置と係数を合わせられます。
- Gバーの緑と赤が逆 — 設定の「加速・減速方向を反転」をONにしてください。傾きと画面の向きは自動で補正されます。
- ブリッピングインジケーターが出ない — 1段下のギヤ比から計算するため、その段が未学習・未入力だと表示されません。設定でブリッピング支援がONであること、2速以上かつ15 km/h以上で走行していることもご確認ください。
- 設定はどこ? — メイン画面をタップすると設定ボタンが表示されます。
プライバシー
本アプリはデータを収集しません。詳しくはプライバシーポリシーをご覧ください。
不具合のご報告やご要望など、その他のお問い合わせも上記メールアドレスまでお願いいたします。